Today's KNOWLEDGE Share: Waste Plastics into Valuable Carbon Nanotubes

-

Today's KNOWLEDGE Share

New Research Converts Waste Plastics into Valuable Carbon Nanotubes

A research team in the Department of Energy and Chemical Engineering at UNIST has unveiled an innovative technology for converting waste plastics into carbon nanotubes (CNTs), a high-value material that plays a critical role in achieving carbon neutrality and promoting a circular economy.


Demonstrating Mass-production of Low Emissions CNTs:

Led by Professor Kwangjin An and Professor Hankwon Lim in the School of Energy and Chemical Engineering and the Graduate School of Carbon Neutrality at UNIST, the joint research team developed a method to produce carbon nanotubes using mixed gases generated from waste mask substances.


During the pyrolysis of waste plastics, these materials are transformed into hydrocarbon gases, including methane, ethylene, and propylene. The researchers harness these gases, subjecting them to high-temperature treatment to create CNTs.


The carbon nanotubes generated through this upcycling process are eco-friendly, producing lower carbon dioxide emissions compared to traditional methane and hydrogen-based methods. Notably, this approach eliminates the need for a waste separation process, streamlining the procedure.


By utilizing the gases produced from the thermal decomposition of mask waste, the research team demonstrated that carbon nanotubes can be mass-produced at a low cost. Remarkably, the upcycling process operates at costs comparable to existing methods, despite the complexity of the system.


Scaling Up CNT Production with Renewables

In addition, the research team has outlined a carbon neutrality strategy through scenario analyses utilizing renewable energy sources. This study marks the first economic and environmental evaluation of carbon nanotube production via waste plastic upcycling, revealing a promising avenue for transforming plastic waste into high-value materials.


First authors Kim Hee-hyang and Nam Eon-woo stated, “The process can achieve low production costs if scaled up and if supply and demand for electricity are managed effectively using renewable energy. This would result in a significant reduction in carbon dioxide emissions.”


Professors Hankwon Lim and Kwanjin An emphasized, “An increase in carbon nanotube supply due to advancements in pyrolysis technology will also enhance energy security.”


This research was supported by the Carbon Neutrality Demonstration and Research Center of UNIST, the Agency for Defense Development, and the National Research Foundation of Korea (NRF) funded by the Ministry of Science and ICT (MSIT) and the Ministry of Trade, Industry and Energy (MOTIE), along with contributions from JEIO Co. The findings were published online in the international journal, Chemical Engineering Journal on June 28, 2024.


Source: UNIST/www.polymer-additives.specialchem.com

Comments

Post a Comment

Popular posts from this blog

Today's KNOWLEDGE Share:PLA BOTTLE

-
Image
Today's KNOWLEDGE Share Ever wondered how we can reduce plastic pollution in India? The Mysuru-based Defence Food Research Laboratory (DFRL), affiliated with the DRDO, has launched an eco-friendly remedy with the introduction of biodegradable water bottles. Crafted from sustainable Polylactic acid (PLA) material, these bottles not only combat plastic waste but also contribute to reducing the overall carbon footprint. The best thing about this bottle is its all-encompassing sustainability approach – the bottle, cap, and label are all compostable. This innovation, derived from 100% bio-based and renewable sources, sets us on a path towards environmental conservation and fosters a greener and more sustainable future. Source:The Better India #polymers #bioplastics #pla   #compostable   #ecofriendly   #sustainability
Read more

Today's KNOWLEDGE Share:High and low shear rate changes in Rheology

-
Image
Today's KNOWLEDGE Share If a relatively high Mw grade flows from thin to thick, as shown in the picture, and if the time needed to fill the thick section is way shorter than the average polymer relaxation time, the polymer will not be able to reach its higher viscosity (corresponding to higher thickness/lower shear-rate). I am assuming here the polymer reached equilibrium low viscosity in the thin section, say for instance because it is much longer. Any pressure prediction not accounting for transient rheology would then overpredict the pressure to fill.Of course the diverging flow will further complicate the situation and mess with the molecular orientation created in the thin section, but to what extent ? Since this is more of a reasonable "conjecture", don't take this for granted, and discuss or share your opinion in the comments. There are hundreds of Rheology papers on the "4:1 contraction flow". Not sure I have ever seen any on the..."1:4 expansio
Read more

Bibby Marine Orders First Battery and Methanol Powered eCSOV

-
Image
  A shipbuilding contract has been completed for what is being called the “world’s first truly zero-emission, electric Commission Service Operation Vessel,” which is being built as part of UK sponsored demonstration project. The ship is expected to enter service in the UK in 2026 using a combination of a powerful battery system along with dual-fuel methanol engines. A coalition of leading maritime companies led by Bibby Marine proposed the project as part of the UK’s Zero Emission Vessels and Infrastructure (ZEVI) project staged by the UK Department of Transportation. A total of £80 million was awarded to 10 projects in the 2022 round with the Bibby effort being   awarded   $25 million. They estimated the cost of the project for the vessel at $37.5 million total. Bibby Marine reports that it completed a tender process and has selected Gondan to build the vessel. The Asturias shipyard in Spain won out of a variety of yards in the UK and internationally. Bibby cites the timeline, budget,
Read more