SABIC OPENS MULTI- MILLION-DOLLAR ULTEM™ RESIN MANUFACTURING FACILITY IN SINGAPORE

-

SABIC, a global diversified chemicals company, today announced the official launch of its new US$170 (S$220) million ULTEM™ resin manufacturing facility in Singapore, marking the company’s first advanced specialty chemical manufacturing facility in the region producing the high-performance thermoplastic, ULTEM™ resin.


The new facility is a strategic move to support SABIC’s goal of increasing global ULTEM™ specialty resin production by more than 50%, responding to the growing demand from high-tech and manufacturing industries in the Asia-Pacific region, including Japan and China.


The facility opening was officiated by Ms. Low Yen Ling, Senior Minister of State for the Ministry of Trade and Industry (MTI) and Ministry of Culture, Community and Youth (MCCY), Eng. Khalid H. Al-Dabbagh, Chairman of the Board of Directors of SABIC, Eng. Abdulrahman Al-Fageeh, SABIC Chief Executive Officer, and Mr. Omar Al-Harthi, Deputy Head of Mission, Embassy of the Kingdom of Saudi Arabia in Singapore.

Supported by the Singapore Economic Development Board (EDB), the new Singapore facility reinforces SABIC’s commitment to localize a reliable supply of high performance materials that support complex and demanding supply chain requirements.


Ms. Low Yen Ling, Senior Minister of State for the Ministry of Trade and Industry (MTI) and Ministry of Culture, Community and Youth (MCCY) said, “The opening of SABIC’s new facility underscores Singapore’s role as a gateway to Asia and a leading hub for the chemicals industry.”

Eng. Abdulrahman Al-Fageeh, CEO, SABIC said, “We’re excited to leverage SABIC’s advanced manufacturing capabilities to produce one of the world’s most advanced plastics in Singapore. The ULTEM resin facility reflects our long-term commitment to the region’s high-tech economies and advanced manufacturing sectors, supporting the growth of advanced applications. Singapore’s widely networked trade agreements also provides us with competitive access to markets in the region.”


Lim Wey Len, Executive Vice President, Singapore Economic Development Board said, “The opening of SABIC’s new ULTEM plant reflects its confidence in Singapore as a hub to capture the growing demand for high-performance specialty chemicals in Asia. We look forward to how the new plant’s advanced manufacturing capabilities will boost our chemicals sector to meet customers’ needs in growth areas such as mobility and electronics. We continue to welcome like-minded partners like SABIC to invest in our talent and capabilities here in Singapore, to create cutting edge material solutions for the world.”

SABIC’S ROLE IN SINGAPORE


source:SABIC


Comments

Post a Comment

Popular posts from this blog

Today's KNOWLEDGE Share:PLA BOTTLE

-
Image
Today's KNOWLEDGE Share Ever wondered how we can reduce plastic pollution in India? The Mysuru-based Defence Food Research Laboratory (DFRL), affiliated with the DRDO, has launched an eco-friendly remedy with the introduction of biodegradable water bottles. Crafted from sustainable Polylactic acid (PLA) material, these bottles not only combat plastic waste but also contribute to reducing the overall carbon footprint. The best thing about this bottle is its all-encompassing sustainability approach – the bottle, cap, and label are all compostable. This innovation, derived from 100% bio-based and renewable sources, sets us on a path towards environmental conservation and fosters a greener and more sustainable future. Source:The Better India #polymers #bioplastics #pla   #compostable   #ecofriendly   #sustainability
Read more

Today's KNOWLEDGE Share:High and low shear rate changes in Rheology

-
Image
Today's KNOWLEDGE Share If a relatively high Mw grade flows from thin to thick, as shown in the picture, and if the time needed to fill the thick section is way shorter than the average polymer relaxation time, the polymer will not be able to reach its higher viscosity (corresponding to higher thickness/lower shear-rate). I am assuming here the polymer reached equilibrium low viscosity in the thin section, say for instance because it is much longer. Any pressure prediction not accounting for transient rheology would then overpredict the pressure to fill.Of course the diverging flow will further complicate the situation and mess with the molecular orientation created in the thin section, but to what extent ? Since this is more of a reasonable "conjecture", don't take this for granted, and discuss or share your opinion in the comments. There are hundreds of Rheology papers on the "4:1 contraction flow". Not sure I have ever seen any on the..."1:4 expansio
Read more

Bibby Marine Orders First Battery and Methanol Powered eCSOV

-
Image
  A shipbuilding contract has been completed for what is being called the “world’s first truly zero-emission, electric Commission Service Operation Vessel,” which is being built as part of UK sponsored demonstration project. The ship is expected to enter service in the UK in 2026 using a combination of a powerful battery system along with dual-fuel methanol engines. A coalition of leading maritime companies led by Bibby Marine proposed the project as part of the UK’s Zero Emission Vessels and Infrastructure (ZEVI) project staged by the UK Department of Transportation. A total of £80 million was awarded to 10 projects in the 2022 round with the Bibby effort being   awarded   $25 million. They estimated the cost of the project for the vessel at $37.5 million total. Bibby Marine reports that it completed a tender process and has selected Gondan to build the vessel. The Asturias shipyard in Spain won out of a variety of yards in the UK and internationally. Bibby cites the timeline, budget,
Read more