Today's KNOWLEDGE Share :Carbon fiber sheet used portable Displays VAIO Vision

-

Today's KNOWLEDGE Share

Tenax™ TPCL and Teijin's Panlite® Sheet are Used for the Housing of the World's Lightest Portable Displays VAIO Vision

Teijin Limited announced today that Teijin’s Tenax™ TPCL, a carbon fiber intermediate material, and its Panlite® Sheet, a polycarbonate (PC) product, the housing of the world's lightest portable displays developed by VAIO Corporation (hereinafter VAIO). The VAIO Vision+™ 14 and the VAIO Vision+™ 14P, subsequently referred to collectively as VAIO Vision+™, were launched by the VAIO in Japan in early July.

The characteristics of the Teijin materials have made it possible to achieve the world's lightest portable display, which weighs approximately 325 g and is approximately 3.9 mm thin at its thinnest point.


Tenax™ TPCL intermediate, used for the VAIO Vision+™ housing’s top and bottom layers of the sandwich construction, is a sheet-like material made of woven carbon fiber impregnated with thermoplastic resin. It is lightweight, resistant to heat and impact, strong and rigid, and also meets flame retardancy requirements for electrical products. In addition, Panlite® Sheet, made from PC resin and used for the middle layer, has excellent dimensional stability, is lightweight, and has impact resistance.


Reduced CO2 and Easier Manufacturing:

Conventional housings use metal parts for assembly, which need to be installed during the manufacturing process. However, the housing of the new displays, which has a structure that sandwiches Panlite® Sheet between Tenax™ TPCL layers, achieves the shape and strength of the connections necessary for assembly without the need for metal parts. This material solution makes it possible to manufacture complex, three-dimensional shapes in a single molding step, which helps reduce the number of steps required to manufacture the housing and also cuts CO2 emissions.


The Teijin Group aims to become "a company that protects the global environment," embodying its long-term vision of becoming "a company that supports the society of the future," and will continue to utilize a wide range of highly functional materials to provide solutions in a variety of fields.


source:Teijin/azom.com


Comments

Post a Comment

Popular posts from this blog

Today's KNOWLEDGE Share:PLA BOTTLE

-
Image
Today's KNOWLEDGE Share Ever wondered how we can reduce plastic pollution in India? The Mysuru-based Defence Food Research Laboratory (DFRL), affiliated with the DRDO, has launched an eco-friendly remedy with the introduction of biodegradable water bottles. Crafted from sustainable Polylactic acid (PLA) material, these bottles not only combat plastic waste but also contribute to reducing the overall carbon footprint. The best thing about this bottle is its all-encompassing sustainability approach – the bottle, cap, and label are all compostable. This innovation, derived from 100% bio-based and renewable sources, sets us on a path towards environmental conservation and fosters a greener and more sustainable future. Source:The Better India #polymers #bioplastics #pla   #compostable   #ecofriendly   #sustainability
Read more

Today's KNOWLEDGE Share:High and low shear rate changes in Rheology

-
Image
Today's KNOWLEDGE Share If a relatively high Mw grade flows from thin to thick, as shown in the picture, and if the time needed to fill the thick section is way shorter than the average polymer relaxation time, the polymer will not be able to reach its higher viscosity (corresponding to higher thickness/lower shear-rate). I am assuming here the polymer reached equilibrium low viscosity in the thin section, say for instance because it is much longer. Any pressure prediction not accounting for transient rheology would then overpredict the pressure to fill.Of course the diverging flow will further complicate the situation and mess with the molecular orientation created in the thin section, but to what extent ? Since this is more of a reasonable "conjecture", don't take this for granted, and discuss or share your opinion in the comments. There are hundreds of Rheology papers on the "4:1 contraction flow". Not sure I have ever seen any on the..."1:4 expansio
Read more

Bibby Marine Orders First Battery and Methanol Powered eCSOV

-
Image
  A shipbuilding contract has been completed for what is being called the “world’s first truly zero-emission, electric Commission Service Operation Vessel,” which is being built as part of UK sponsored demonstration project. The ship is expected to enter service in the UK in 2026 using a combination of a powerful battery system along with dual-fuel methanol engines. A coalition of leading maritime companies led by Bibby Marine proposed the project as part of the UK’s Zero Emission Vessels and Infrastructure (ZEVI) project staged by the UK Department of Transportation. A total of £80 million was awarded to 10 projects in the 2022 round with the Bibby effort being   awarded   $25 million. They estimated the cost of the project for the vessel at $37.5 million total. Bibby Marine reports that it completed a tender process and has selected Gondan to build the vessel. The Asturias shipyard in Spain won out of a variety of yards in the UK and internationally. Bibby cites the timeline, budget,
Read more