Today's KNOWLEDGE Share:DOW's Bio-based EPDM

-

Today's KNOWLEDGE Share

Dow announces bio-based NORDEL™ REN EPDM at DKT 2024

 Dow is proud to announce at the German Rubber Conference (DKT) 2024 the launch of NORDEL™ REN Ethylene Propylene Diene Terpolymers (EPDM), a bio-based version of Dow’s EPDM rubber material that goes into automotive, infrastructure and consumer applications.


A key component of automotive weatherseals and hoses, Dow aims to support not just the automotive industry in achieving its sustainability goals with the launch of NORDEL™ REN EPDM, but as EPDM also goes into building profiles, roofing membranes, wire and cable, among others, NORDEL™ REN EPDM can help the decarbonization of building and construction and more.


The plant-based EPDM will be made through an ISCC PLUS certified mass balance system which traces the flow of bio-based raw material through a complex value chain and attributes it through verifiable bookkeeping.


Dow’s Path to Zero

The arrival of NORDEL™ REN EPDM is part of Dow’s continuous endeavors towards carbon neutrality. The technology behind NORDEL™ EPDM production, Dow’s Advanced Molecular Catalyst, already results in a highly efficient process that uses 24% less energy than the conventional Ziegler-Natta process, and thus 39% lower carbon footprint for the standard NORDEL™ EPDM grades, which has been validated by a third-party life cycle analysis (LCA).


Discover Dow’s portfolio of rubber technologies for decarbonization on show at DKT 2024

NORDEL™ REN is featured at the DKT 2024 along with a range of EPDM and Silicone rubber technologies on show that help lower the carbon footprint of diverse industries:

1. SILASTIC™ Solutions for Electric Vehicles (EV) including High Consistency Rubbers (HCR) and Liquid Silicone Rubbers (LSR) for fire protection and connectivity, advancing electrification of the automotive industry to reduce tailpipe emissions

2. SILASTIC™ Silicone for Self-Sealing Tires, designed to form a self-sealing layer on the inner surface of a tire, allowing long-distance driving without loss of air pressure and supporting easy disassembly of vehicle part for separate recycling of silicone

3. NORDEL™ EPDM innovation for Microdense Weatherseals, aiding in the reduction of overall density of weatherseals and of tailpipe emissions through lightweighting, by bringing enough strength to maintain critical performance of the rubber material

4. Dow’s patented innovation for the creation of LUXSENSE™ Silicone Synthetic Leather, the world’s first silicone-based luxury synthetic material bringing sustainability with lower carbon emissions cradle to gate, solvent-free fabrication process, and animal-free, while offering exceptional haptic feedback and remarkable abrasion resistance

Visit hall 8, stand 103a from 1 – 4 July in Nuremberg, Germany, to learn more about Dow’s innovative rubber options to advance a more sustainable future.


source:Dow

Comments

Post a Comment

Popular posts from this blog

Today's KNOWLEDGE Share:PLA BOTTLE

-
Image
Today's KNOWLEDGE Share Ever wondered how we can reduce plastic pollution in India? The Mysuru-based Defence Food Research Laboratory (DFRL), affiliated with the DRDO, has launched an eco-friendly remedy with the introduction of biodegradable water bottles. Crafted from sustainable Polylactic acid (PLA) material, these bottles not only combat plastic waste but also contribute to reducing the overall carbon footprint. The best thing about this bottle is its all-encompassing sustainability approach – the bottle, cap, and label are all compostable. This innovation, derived from 100% bio-based and renewable sources, sets us on a path towards environmental conservation and fosters a greener and more sustainable future. Source:The Better India #polymers #bioplastics #pla   #compostable   #ecofriendly   #sustainability
Read more

Today's KNOWLEDGE Share:High and low shear rate changes in Rheology

-
Image
Today's KNOWLEDGE Share If a relatively high Mw grade flows from thin to thick, as shown in the picture, and if the time needed to fill the thick section is way shorter than the average polymer relaxation time, the polymer will not be able to reach its higher viscosity (corresponding to higher thickness/lower shear-rate). I am assuming here the polymer reached equilibrium low viscosity in the thin section, say for instance because it is much longer. Any pressure prediction not accounting for transient rheology would then overpredict the pressure to fill.Of course the diverging flow will further complicate the situation and mess with the molecular orientation created in the thin section, but to what extent ? Since this is more of a reasonable "conjecture", don't take this for granted, and discuss or share your opinion in the comments. There are hundreds of Rheology papers on the "4:1 contraction flow". Not sure I have ever seen any on the..."1:4 expansio
Read more

Bibby Marine Orders First Battery and Methanol Powered eCSOV

-
Image
  A shipbuilding contract has been completed for what is being called the “world’s first truly zero-emission, electric Commission Service Operation Vessel,” which is being built as part of UK sponsored demonstration project. The ship is expected to enter service in the UK in 2026 using a combination of a powerful battery system along with dual-fuel methanol engines. A coalition of leading maritime companies led by Bibby Marine proposed the project as part of the UK’s Zero Emission Vessels and Infrastructure (ZEVI) project staged by the UK Department of Transportation. A total of £80 million was awarded to 10 projects in the 2022 round with the Bibby effort being   awarded   $25 million. They estimated the cost of the project for the vessel at $37.5 million total. Bibby Marine reports that it completed a tender process and has selected Gondan to build the vessel. The Asturias shipyard in Spain won out of a variety of yards in the UK and internationally. Bibby cites the timeline, budget,
Read more