Today's KNOWLEDGE Share :CO2 derived sustainable polyester fiber

-

Today's KNOWLEDGE Share

World’s first supply chain established for more sustainable polyester fiber based on CO2-derived material as well as renewable and bio-based materials

A consortium of seven companies across five countries has jointly established a supply chain for more sustainable polyester fiber. Instead of fossil materials, renewable and bio-based materials as well as carbon capture and utilization (CCU*) will be used in the manufacturing of polyester fibers for The North Face brand in Japan. The consortium parties are Goldwin, in the role of project owner, Mitsubishi Corporation, Chiyoda Corporation (all three from Japan), SK geo centric (South Korea), Indorama Ventures (Thailand), India Glycols (India) and Neste. 



Neste will provide renewable Neste RE™ as one of the required ingredients for polyester production. The polyester fiber produced in the project is planned to be used by Goldwin for a part of The North Face products, including sports uniforms, in July 2024. After that, the launch of further Goldwin products and brands will be considered. 


The seven companies apply a mass balancing approach to ensure credible traceability of material streams throughout the supply chain and will jointly continue to proactively promote the defossilization of materials to contribute to a more sustainable society.


Regarding the production of para-xylene derived from CO2 as a raw material, the University of Toyama, HighChem Company Limited, Nippon Steel Engineering Co. Ltd., Nippon Steel Corporation, Chiyoda Corporation and Mitsubishi Corporation were granted a NEDO project (New Energy and Industrial Technology Development Organization) status in 2020: "Technology Development for Carbon Recycling and Next Generation Thermal Power Generation/Technology Development for CO2 Emission Reduction and Effective Utilization". They are conducting joint research and development. This project is to supply CO2-derived para-xylene in the course of a trial. It has been produced during the operation process of a pilot plant installed in Chiyoda Corporation's Koyasu Research Park since March 2022.


source:Neste Corporation

Comments

Post a Comment

Popular posts from this blog

Today's KNOWLEDGE Share:PLA BOTTLE

-
Image
Today's KNOWLEDGE Share Ever wondered how we can reduce plastic pollution in India? The Mysuru-based Defence Food Research Laboratory (DFRL), affiliated with the DRDO, has launched an eco-friendly remedy with the introduction of biodegradable water bottles. Crafted from sustainable Polylactic acid (PLA) material, these bottles not only combat plastic waste but also contribute to reducing the overall carbon footprint. The best thing about this bottle is its all-encompassing sustainability approach – the bottle, cap, and label are all compostable. This innovation, derived from 100% bio-based and renewable sources, sets us on a path towards environmental conservation and fosters a greener and more sustainable future. Source:The Better India #polymers #bioplastics #pla   #compostable   #ecofriendly   #sustainability
Read more

Today's KNOWLEDGE Share:High and low shear rate changes in Rheology

-
Image
Today's KNOWLEDGE Share If a relatively high Mw grade flows from thin to thick, as shown in the picture, and if the time needed to fill the thick section is way shorter than the average polymer relaxation time, the polymer will not be able to reach its higher viscosity (corresponding to higher thickness/lower shear-rate). I am assuming here the polymer reached equilibrium low viscosity in the thin section, say for instance because it is much longer. Any pressure prediction not accounting for transient rheology would then overpredict the pressure to fill.Of course the diverging flow will further complicate the situation and mess with the molecular orientation created in the thin section, but to what extent ? Since this is more of a reasonable "conjecture", don't take this for granted, and discuss or share your opinion in the comments. There are hundreds of Rheology papers on the "4:1 contraction flow". Not sure I have ever seen any on the..."1:4 expansio
Read more

Covestro and Arcesso's Arfinio® Technology is “Winner” in "German Innovation Award 2024"

-
Image
The Innovation Award honors products, projects, and pioneering achievements that sustainably improve life Arfinio® earns “Winner”-prize in the category "Excellence in B2B: Materials and Surfaces" This technological breakthrough enables the rapid production of lightweight, repairable, and recyclable solid surface materials. Covestro, one of the world's leading manufacturers of polymer materials and components, has been awarded “Winner” of the "German Innovation Award 2024" for outstanding innovation achievements in the category "Excellence in B2B: Materials and Surfaces" for its Arfinio ®  technology. The award is presented by the "German Design Council." Candidates submit projects that have been launched on the market no longer than five years ago, but they can also be nominated by the council. The evaluation is carried out by an independent, interdisciplinary expert jury. The award ceremony took place on May 14 in front of around 300 invited
Read more