Today's KNOWLEDGE Share : Issues with color masterbatches in Injection Molding

-

Today's KNOWLEDGE Share

Understanding Common Issues with Color Masterbatches in Injection Molding


The use of color masterbatches is prevalent in injection molding. However, over the years, I have frequently encountered several issues that typically result in surface defects on the molded parts.


These issues can be categorized into three main scenarios:


1. Incompatible Carrier Materials


Sometimes, masterbatches (e.g., with 50% pigment and 50% carrier) use a high-flow carrier like LLDPE, even when the host polymer to be colored is not LLDPE-based.


Issue: The incompatible high-flow carrier is pushed to the surface by hydrodynamic forces. For instance, small amounts of LLDPE in a nylon part can readily create blisters or delamination.


2. Neglecting to Dry the Masterbatch


In nylon or polyester parts, even when the masterbatch uses the correct carrier (same as the host matrix to be colored), users often neglect to dry the masterbatch, drying only the bulk resin to be molded.


Issue: Users may assume that the small amount of masterbatch added doesn’t need drying. However, a very wet, small amount of carrier can cause surface blooming, silver streaks, and potentially significant hydrolytic degradation issues in sensitive materials like PET or PBT.


3. Improper Dispersion of Masterbatch


Even when the masterbatch uses the correct carrier and is properly dried before feeding into the hopper, part issues can still arise.


Issue: The problem often stems from less than perfect dispersion of the masterbatch in the injection molding machine screw. These screws are not always ideally designed and may lack the ability to fully disperse the pigment, leading to color issues due to inhomogeneous color concentrate.


Understanding and addressing these common issues can significantly improve the quality of injection molded parts. Ensuring compatibility of carriers, proper drying of materials, and optimal dispersion techniques are crucial steps in achieving defect-free products.


credit:Vito leo


#plastics #injectionmolding #plasticmasterbatch


Comments

Post a Comment

Popular posts from this blog

Today's KNOWLEDGE Share:PLA BOTTLE

-
Image
Today's KNOWLEDGE Share Ever wondered how we can reduce plastic pollution in India? The Mysuru-based Defence Food Research Laboratory (DFRL), affiliated with the DRDO, has launched an eco-friendly remedy with the introduction of biodegradable water bottles. Crafted from sustainable Polylactic acid (PLA) material, these bottles not only combat plastic waste but also contribute to reducing the overall carbon footprint. The best thing about this bottle is its all-encompassing sustainability approach – the bottle, cap, and label are all compostable. This innovation, derived from 100% bio-based and renewable sources, sets us on a path towards environmental conservation and fosters a greener and more sustainable future. Source:The Better India #polymers #bioplastics #pla   #compostable   #ecofriendly   #sustainability
Read more

Today's KNOWLEDGE Share:High and low shear rate changes in Rheology

-
Image
Today's KNOWLEDGE Share If a relatively high Mw grade flows from thin to thick, as shown in the picture, and if the time needed to fill the thick section is way shorter than the average polymer relaxation time, the polymer will not be able to reach its higher viscosity (corresponding to higher thickness/lower shear-rate). I am assuming here the polymer reached equilibrium low viscosity in the thin section, say for instance because it is much longer. Any pressure prediction not accounting for transient rheology would then overpredict the pressure to fill.Of course the diverging flow will further complicate the situation and mess with the molecular orientation created in the thin section, but to what extent ? Since this is more of a reasonable "conjecture", don't take this for granted, and discuss or share your opinion in the comments. There are hundreds of Rheology papers on the "4:1 contraction flow". Not sure I have ever seen any on the..."1:4 expansio
Read more

Bibby Marine Orders First Battery and Methanol Powered eCSOV

-
Image
  A shipbuilding contract has been completed for what is being called the “world’s first truly zero-emission, electric Commission Service Operation Vessel,” which is being built as part of UK sponsored demonstration project. The ship is expected to enter service in the UK in 2026 using a combination of a powerful battery system along with dual-fuel methanol engines. A coalition of leading maritime companies led by Bibby Marine proposed the project as part of the UK’s Zero Emission Vessels and Infrastructure (ZEVI) project staged by the UK Department of Transportation. A total of £80 million was awarded to 10 projects in the 2022 round with the Bibby effort being   awarded   $25 million. They estimated the cost of the project for the vessel at $37.5 million total. Bibby Marine reports that it completed a tender process and has selected Gondan to build the vessel. The Asturias shipyard in Spain won out of a variety of yards in the UK and internationally. Bibby cites the timeline, budget,
Read more