Today's KNOWLEDGE Share:POM vs Nylon

-

Today's KNOWLEDGE Share

Comparative Analysis of POM with Other Plastics:

Some of the key advantages and limitations of POM compared to other plastics are highlighted below:



POM vs Nylon:

POM has lower moisture absorption and better dimensional stability than nylon

It has higher tensile strength, hardness and modulus than nylon

Nylon offers higher toughness, ductility and impact strength compared to POM

Nylon has better chemical resistance than POM, especially to bases, oils and greases

POM provides lower coefficient of friction than nylon


POM vs Polycarbonate:

POM has much higher strength, hardness and stiffness than polycarbonate

PC offers very high impact resistance compared to brittle

POMPolycarbonate has superior temperature resistance up to 140°C vs 90°C for POM

POM has lower moisture absorption and better dimensional stability

PC has higher ductility and fracture toughness compared to POM


POM vs Polyimide:

Polyimide can withstand much higher temperatures than POM

It has excellent strength retention at high temperatures vs POM

POM offers better impact strength and machinability

Polyimide has superior wear resistance and chemical resistance

POM has lower density and moisture absorption compared to polyimide


source:beeplastic.com

Comments

Post a Comment

Popular posts from this blog

Today's KNOWLEDGE Share:PLA BOTTLE

-
Image
Today's KNOWLEDGE Share Ever wondered how we can reduce plastic pollution in India? The Mysuru-based Defence Food Research Laboratory (DFRL), affiliated with the DRDO, has launched an eco-friendly remedy with the introduction of biodegradable water bottles. Crafted from sustainable Polylactic acid (PLA) material, these bottles not only combat plastic waste but also contribute to reducing the overall carbon footprint. The best thing about this bottle is its all-encompassing sustainability approach – the bottle, cap, and label are all compostable. This innovation, derived from 100% bio-based and renewable sources, sets us on a path towards environmental conservation and fosters a greener and more sustainable future. Source:The Better India #polymers #bioplastics #pla   #compostable   #ecofriendly   #sustainability
Read more

Today's KNOWLEDGE Share:High and low shear rate changes in Rheology

-
Image
Today's KNOWLEDGE Share If a relatively high Mw grade flows from thin to thick, as shown in the picture, and if the time needed to fill the thick section is way shorter than the average polymer relaxation time, the polymer will not be able to reach its higher viscosity (corresponding to higher thickness/lower shear-rate). I am assuming here the polymer reached equilibrium low viscosity in the thin section, say for instance because it is much longer. Any pressure prediction not accounting for transient rheology would then overpredict the pressure to fill.Of course the diverging flow will further complicate the situation and mess with the molecular orientation created in the thin section, but to what extent ? Since this is more of a reasonable "conjecture", don't take this for granted, and discuss or share your opinion in the comments. There are hundreds of Rheology papers on the "4:1 contraction flow". Not sure I have ever seen any on the..."1:4 expansio
Read more

Bibby Marine Orders First Battery and Methanol Powered eCSOV

-
Image
  A shipbuilding contract has been completed for what is being called the “world’s first truly zero-emission, electric Commission Service Operation Vessel,” which is being built as part of UK sponsored demonstration project. The ship is expected to enter service in the UK in 2026 using a combination of a powerful battery system along with dual-fuel methanol engines. A coalition of leading maritime companies led by Bibby Marine proposed the project as part of the UK’s Zero Emission Vessels and Infrastructure (ZEVI) project staged by the UK Department of Transportation. A total of £80 million was awarded to 10 projects in the 2022 round with the Bibby effort being   awarded   $25 million. They estimated the cost of the project for the vessel at $37.5 million total. Bibby Marine reports that it completed a tender process and has selected Gondan to build the vessel. The Asturias shipyard in Spain won out of a variety of yards in the UK and internationally. Bibby cites the timeline, budget,
Read more