𝐓𝐨𝐝𝐚𝐲'𝐬 𝐊𝐍𝐎𝐖𝐋𝐄𝐃𝐆𝐄 𝐒𝐡𝐚𝐫𝐞 : 𝐇𝐨𝐰 𝐌𝐮𝐜𝐡 𝐃𝐢𝐬𝐩𝐞𝐫𝐬𝐚𝐧𝐭 𝐒𝐡𝐨𝐮𝐥𝐝 𝐘𝐨𝐮 𝐀𝐝𝐝? 𝟑 𝐒𝐭𝐞𝐩𝐬 𝐭𝐨 𝐅𝐢𝐧𝐝 𝐭𝐡𝐞 𝐑𝐢𝐠𝐡𝐭 𝐃𝐨𝐬𝐚𝐠𝐞

𝐓𝐨𝐝𝐚𝐲'𝐬 𝐊𝐍𝐎𝐖𝐋𝐄𝐃𝐆𝐄 𝐒𝐡𝐚𝐫𝐞

𝐇𝐨𝐰 𝐌𝐮𝐜𝐡 𝐃𝐢𝐬𝐩𝐞𝐫𝐬𝐚𝐧𝐭 𝐒𝐡𝐨𝐮𝐥𝐝 𝐘𝐨𝐮 𝐀𝐝𝐝? 𝟑 𝐒𝐭𝐞𝐩𝐬 𝐭𝐨 𝐅𝐢𝐧𝐝 𝐭𝐡𝐞 𝐑𝐢𝐠𝐡𝐭 𝐃𝐨𝐬𝐚𝐠𝐞

Adding too much dispersant wastes money. Adding too little can compromise dispersion efficiency.

So, how do you determine the optimal dosage?


The answer is not simply based on pigment loading. It depends largely on the total surface area of the pigment particles that needs to be covered.

Here are three practical steps to find the right dosage.

**STEP 1 | Start with Experience-Based Ratios**

A common starting point is to calculate the active dispersant content as a percentage of pigment weight.

Typical reference ranges:

• Inorganic pigments (TiO₂, iron oxide): 1–3%
• General organic pigments: 3–8%
• Difficult-to-disperse organic pigments: 8–15%
• High-color carbon black: 30–100% or higher


For example, to disperse 100 g of organic pigment at 4% active dispersant, using a product with 40% solids:

Actual addition = 4% ÷ 40% = 10 g.

**STEP 2 | Calculate Based on Specific Surface Area**

Pigment particles with smaller sizes generally have larger specific surface areas and require more dispersant.

The calculation is:

Active dispersant (mg) = k × Specific surface area (m²/g) × Pigment weight (g)

Reference k values:
• Inorganic pigments: 0.3–0.8 mg/m²
• Organic pigments: 0.8–2 mg/m²
• Carbon black: 2–6 mg/m²


This method provides a more realistic estimate of dispersant demand.

**STEP 3 | Validate Through Laboratory Testing**

Calculations provide a starting point, but the actual formulation determines the final dosage.

Run 5–7 dosage gradients and monitor three key indicators:

1. Viscosity: Does it decrease and eventually reach a plateau?
2. Fineness and particle size: Does further addition improve dispersion?
3. Side effects: Foaming, tackiness, slower drying or reduced water resistance.


**The key is to find the saturation point.**

The optimal dosage is usually around the minimum-viscosity point or where the viscosity curve begins to level off.

Beyond this point, excess free dispersant may increase costs and introduce unwanted side effects.

**A practical rule: Estimate → Calculate → Validate.**

Don't rely on pigment weight alone. Understand the particle surface area, then let laboratory testing confirm the optimal dosage.

source : Jack Li

#Dispersants #PigmentDispersion #Coatings #PaintFormulation #FormulationChemistry #CoatingAdditives #Rheology #IndustrialCoatings


Comments

Popular posts from this blog

Today's KNOWLEDGE Share : Robotic 3D printing can compete with traditional boatbuilding

Today's KNOWLEDGE Share : A BUG IN INJECTION MOLDING

𝐓𝐨𝐝𝐚𝐲'𝐬 𝐊𝐍𝐎𝐖𝐋𝐄𝐃𝐆𝐄 𝐒𝐡𝐚𝐫𝐞 : 𝐀𝐍𝐓𝐈-𝐎𝐗𝐈𝐃𝐀𝐍𝐓 – 𝐓𝐡𝐞𝐫𝐦𝐚𝐥 𝐚𝐧𝐝 𝐏𝐫𝐨𝐜𝐞𝐬𝐬 𝐏𝐫𝐨𝐭𝐞𝐜𝐭𝐢𝐨𝐧