𝐓𝐨𝐝𝐚𝐲'𝐬 𝐊𝐍𝐎𝐖𝐋𝐄𝐃𝐆𝐄 𝐒𝐡𝐚𝐫𝐞 : 𝐒𝐚𝐦𝐞 𝐩𝐨𝐥𝐲𝐦𝐞𝐫, 𝐒𝐚𝐦𝐞 𝐦𝐚𝐧𝐮𝐟𝐚𝐜𝐭𝐮𝐫𝐢𝐧𝐠 𝐭𝐞𝐜𝐡𝐧𝐨𝐥𝐨𝐠𝐲, 𝐁𝐮𝐭 𝐮𝐩 𝐭𝐨 𝟕𝟎% 𝐝𝐢𝐟𝐟𝐞𝐫𝐞𝐧𝐜𝐞 𝐢𝐧 𝐞𝐥𝐨𝐧𝐠𝐚𝐭𝐢𝐨𝐧, 𝐖𝐡𝐲?!

𝐓𝐨𝐝𝐚𝐲'𝐬 𝐊𝐍𝐎𝐖𝐋𝐄𝐃𝐆𝐄 𝐒𝐡𝐚𝐫𝐞

𝐒𝐚𝐦𝐞 𝐩𝐨𝐥𝐲𝐦𝐞𝐫,

𝐒𝐚𝐦𝐞 𝐦𝐚𝐧𝐮𝐟𝐚𝐜𝐭𝐮𝐫𝐢𝐧𝐠 𝐭𝐞𝐜𝐡𝐧𝐨𝐥𝐨𝐠𝐲,

𝐁𝐮𝐭 𝐮𝐩 𝐭𝐨 𝟕𝟎% 𝐝𝐢𝐟𝐟𝐞𝐫𝐞𝐧𝐜𝐞 𝐢𝐧 𝐞𝐥𝐨𝐧𝐠𝐚𝐭𝐢𝐨𝐧, 𝐖𝐡𝐲?!

In conventional material selection, mechanical properties are often treated as characteristics of the material itself. However, in Additive Manufacturing, the way a material is deposited can significantly change how the resulting component behaves under mechanical loading.


🔬 In an experimental-numerical investigation of 3D-printed PLA, the influence of filament orientation on tensile behaviour was examined. When the orientation angle decreased from 90° to 0°, Young's modulus increased by approximately 40%, while elongation increased by approximately 70%. Ultimate tensile strength also increased, accompanied by changes in the observed failure mechanisms.

These differences were not simply variations in measured mechanical properties. Microscopic observations revealed distinct fracture behaviours, highlighting the importance of filament alignment and interlayer bonding in determining how a printed structure responds to loading. The investigation also combined experimental tensile testing with Tsai-Hill and Tsai-Wu failure criteria and finite element analysis to examine the prediction of orientation-dependent mechanical behaviour.

The important question is therefore not only which polymer should be selected, but also how its manufactured structure will interact with the mechanical loads encountered in service.

This distinction becomes particularly relevant when moving from prototypes to functional components, where material selection, deposition orientation and mechanical design cannot be considered independently.

📄 Related reference: https://lnkd.in/eVQCcCXr

source : HamidReza Vanaei


#AdditiveManufacturing #MechanicalBehavior #formnext #3DPrinting #PolymerEngineering

Comments

Popular posts from this blog

Today's KNOWLEDGE Share : Robotic 3D printing can compete with traditional boatbuilding

Today's KNOWLEDGE Share : A BUG IN INJECTION MOLDING

𝐓𝐨𝐝𝐚𝐲'𝐬 𝐊𝐍𝐎𝐖𝐋𝐄𝐃𝐆𝐄 𝐒𝐡𝐚𝐫𝐞 : 𝐀𝐍𝐓𝐈-𝐎𝐗𝐈𝐃𝐀𝐍𝐓 – 𝐓𝐡𝐞𝐫𝐦𝐚𝐥 𝐚𝐧𝐝 𝐏𝐫𝐨𝐜𝐞𝐬𝐬 𝐏𝐫𝐨𝐭𝐞𝐜𝐭𝐢𝐨𝐧